Pyramid DC Receiver Manual de instalación descargar pdf (Pagina 16)

Page 16

Pyramid Universal Dome Interface Installation Manual

ADDRESSING A UDI WITH THE PYRAMID 1 KEYBOARD

A UDI can also be addressed using the Pyramid 1 Keyboard. Follow the steps below:

1. Connect up a Pyramid Mk1 Keyboard to the UDI. This can be done directly by connecting the network card on the

keyboard to the Pyramid Data Connection on the UDI, or remotely through the Pyramid network in the normal way.

2. Using the keyboard, insert the Installers Card and log on with the PIN number 1892.

3. Press the key sequence 100 and then the Function key.

The left hand side of the keyboard display will show Fn 0100 to indicate that self binding mode has been invoked.

4. Repeatedly press the List Down key, until the LCD display shows the option Replace RX.

5. Once this option is displayed, select soft key number 1 marked Yes.

At this point, the keyboard is now waiting for the UDI to identify itself using the service PIN.

6. Press the service pin on the UDI.

The UDIs neuron ID is transmitted onto the network and the keyboard display will show the text Receiver

Identified.

7. Type in the node ID you require this UDI to be configured to, and then press the Camera Select key.

After a short delay, the keyboard will then display the message Subnet Node Calculated.

8. After 10 seconds, the keyboard will then log itself out automatically.

Troubleshooting

Q I pressed the service PIN on the UDI, but the keyboard did not show the Receiver Identified message.

A No data is coming through, check the data cabling between the UDI and the keyboard.

Q I got to stage 7, but the Subnet Node Calculated message remained on the keyboard screen and the keyboard did

not log off.

A Data is only being transmitted in one direction. Check to see if the data cable has been connected to the correct

side of the communications card, or if one side of the twisted pair has become disconnected.

Note

The UDI can also be addressed and installed using the Pyramid Installation Tool. This software allows remote

configuration of the Pyramid system using a PC. See the Pyramid Installation Tool Operating Manual for more

details.

ADDRESSING A UDI WITH THE PYRAMID 2 KEYBOARD

Each UDI that is connected to the Pyramid system must be assigned a unique address called a node ID, and an

operator with installer privileges can do this using the Pyramid 2 Keyboard.

Configuration of the UDI requires its service button to be pressed (located on the Dome Data end panel of the

module), and this may be a two man operation if the UDI is located remotely from the keyboard. For this reason, it is

easier to address a UDI before it is added to the network, and this can be done using a special mode of the Pyramid

keyboard called Self-Bind (also known as Fn 100). Self-binding mode is commonly used when configuring telemetry

receivers, or when cameras need to be controlled in a system without a CCTV matrix.

During the self-binding process, the installer can set up the network address, which includes the node IDthe

number that is entered on a keyboard to indicate which device is to be controlled (e.g., Camera receiver number 4).

Once the network address has been configured, the UDI and its associated dome camera can be attached to the

network and controlled through the Pyramid matrix.

To address a UDI in self-binding mode, follow the steps below:

1. Connect up a Pyramid 2 Keyboard to the UDI. This can be done directly by connecting the network card on the

keyboard to the Pyramid Data Connection on the UDI, or remotely through the Pyramid network in the normal way.

2. Log onto the Pyramid 2 Keyboard using the installer password. The Installer Logon screen is displayed, where

you can log on with the PIN number 1892.

3. Press the Function 100 soft-key. The Direct Access screen is displayed.

4. Press the Receiver soft-key.

5. Press the Rx Utilities screen key.

6. Press the Unit Address Type soft-key.

The Addressing screen is displayed.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Comentarios a estos manuales

Sin comentarios

Pyramid DC Receiver Manual de instalación Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Receptor Pyramid DC Receiver